[毕业设计] 颗粒分料机设计 [复制链接]

资料简介：
毕业设计-颗粒分料机设计，说明书共28页，9515字，附任务书、设计图纸、三维图集
摘要：为了提高加工效率，本课题设计了一种出料粒度为15～20mm的颗粒分料机，根据要求设计了锤击部分和反击部分。 物料由进料口进入破碎腔，经过锤头的冲击、剪切、劈碎、折断，实现物料的中碎；锤击的物料冲击到安装在破碎腔内的反击板上，又经过物料与反击板、物料与物料的互相冲击,从而实现了物料的细碎。本机融合了锤式分料机、反击式分料机与颗粒分料机的优点,降低了生料和熟料的入磨粒度，较好地达到了设计要求。
关键词：分料机；反击板；锤头
The designe of Vertical spindle type breaker
Abstract: In order to enhance the processing efficiency, this topic has designed one kind of material granularity is 15 ~ 20mm vertical spindle type breaker, according to requested to design has hammered the part and the counter-attack part. The material by enters the broken cavity, after the hammer head impact, cuts, chops into pieces, breaks off, the realization material center is garrulous; Hammers the material attacks installs in the broken cavity on the counter-attack board, also passes through the material and the counter-attack board, the material and the material mutual impact, thus has realized the material fragmentation. This machine fused the hammer type breaker, the counter-attack type breaker and the vertical spindle type breaker merit, reduced the crude material and the chamotte enters rubs the granularity, has met the design requirements well.
Keywords: breaker; counter-attack board; hammer head

目录
1前言…1
2概述………..2
3 总体方案论证.5
4 颗粒分料机的总体设计…….6
5 颗粒分料机主要参数的确定………9
6 相关零件的设计..22
7 辅助零件的设计……….23
8 结论 ….25
参考文献…….26
致谢….27

技术参数为：
1.进料粒度 <150mm
2.出料粒度 <10mm
3.转子直径 1000mm
3. 生产能力 25-30t/h

资料文件预览：
共2文件夹，23个文件，文件总大小：5.16MB，压缩后大小：3.41MB

• 毕业设计-颗粒分料机设计
• 颗粒分料机
• 装配图.dwg  [387.89KB]
• 制动器.dwg  [215.20KB]
• 制动盘.dwg  [55.99KB]
• 摘要.doc  [25.00KB]
• 压盘.dwg  [102.44KB]
• 三维图集.doc  [1.86MB]
• 目录.doc  [20.50KB]
• 密封盖.dwg  [76.50KB]
• 门.dwg  [84.64KB]
• 料斗.dwg  [56.70KB]
• 壳体.dwg  [105.94KB]
• 进料斗.dwg  [78.22KB]
• 花键轴.dwg  [58.85KB]
• 反击板.dwg  [65.89KB]
• 定位齿块.dwg  [49.65KB]
• 差速锁摇臂轴.dwg  [68.98KB]
• 毕业设计说明书.doc  [1.17MB]
• 毕业设计任务书.doc  [214.00KB]
• N底座.dwg  [124.11KB]
• 4方头螺栓.dwg  [69.07KB]
• 3盖子.dwg  [121.51KB]
• 2隔板.dwg  [86.07KB]
• 1转子.dwg  [102.56KB]