资料简介：
毕业设计-颗粒分料机设计，说明书共28页，9515字，附任务书、设计图纸、三维图集
摘要：为了提高加工效率，本课题设计了一种出料粒度为15～20mm的颗粒分料机，根据要求设计了锤击部分和反击部分。 物料由进料口进入破碎腔，经过锤头的冲击、剪切、劈碎、折断，实现物料的中碎；锤击的物料冲击到安装在破碎腔内的反击板上，又经过物料与反击板、物料与物料的互相冲击,从而实现了物料的细碎。本机融合了锤式分料机、反击式分料机与颗粒分料机的优点,降低了生料和熟料的入磨粒度，较好地达到了设计要求。
关键词：分料机；反击板；锤头
The designe of Vertical spindle type breaker
Abstract: In order to enhance the processing efficiency, this topic has designed one kind of material granularity is 15 ~ 20mm vertical spindle type breaker, according to requested to design has hammered the part and the counter-attack part. The material by enters the broken cavity, after the hammer head impact, cuts, chops into pieces, breaks off, the realization material center is garrulous; Hammers the material attacks installs in the broken cavity on the counter-attack board, also passes through the material and the counter-attack board, the material and the material mutual impact, thus has realized the material fragmentation. This machine fused the hammer type breaker, the counter-attack type breaker and the vertical spindle type breaker merit, reduced the crude material and the chamotte enters rubs the granularity, has met the design requirements well.
Keywords: breaker; counter-attack board; hammer head
目录
1前言…1
2概述………..2
3 总体方案论证.5
4 颗粒分料机的总体设计…….6
5 颗粒分料机主要参数的确定………9
6 相关零件的设计..22
7 辅助零件的设计……….23
8 结论 ….25
参考文献…….26
致谢….27
技术参数为：
1.进料粒度 <150mm
2.出料粒度 <10mm
3.转子直径 1000mm
3. 生产能力 25-30t/h
资料文件预览：
共2文件夹，23个文件，文件总大小：5.16MB，压缩后大小：3.41MB
- 毕业设计-颗粒分料机设计
- 颗粒分料机
装配图.dwg [387.89KB]- 制动器.dwg [215.20KB]
- 制动盘.dwg [55.99KB]
摘要.doc [25.00KB]- 压盘.dwg [102.44KB]
- 三维图集.doc [1.86MB]
- 目录.doc [20.50KB]
- 密封盖.dwg [76.50KB]
- 门.dwg [84.64KB]
- 料斗.dwg [56.70KB]
- 壳体.dwg [105.94KB]
- 进料斗.dwg [78.22KB]
- 花键轴.dwg [58.85KB]
- 反击板.dwg [65.89KB]
- 定位齿块.dwg [49.65KB]
- 差速锁摇臂轴.dwg [68.98KB]
- 毕业设计说明书.doc [1.17MB]
- 毕业设计任务书.doc [214.00KB]
- N底座.dwg [124.11KB]
- 4方头螺栓.dwg [69.07KB]
- 3盖子.dwg [121.51KB]
- 2隔板.dwg [86.07KB]
- 1转子.dwg [102.56KB]
我要下载：颗粒分料机设计
